Extron-electronics DTP HDMI 230 D Setup Guide Manuel d'utilisateur télécharger pdf

DTP DVI 230 D and HDMI 230 D • Setup Guide

This setup guide provides instructions for an experienced installer to set up and operate the

Extron DTP DVI 230 D and DTP HDMI 230 D Extenders.

Installation

Step 1 — Prepare the Mounting Surface

NOTE: Use a wall box with a depth of at least 3.0 inches (7.6 cm).

Alternatively, the included mud ring (MR 200) can be used.

For more information, see the full product user guides at

www.extron.com

a. Place the wall box against the installation surface and mark the

opening guidelines.

TIP: Use a level to mark the opening.

b. Cut out the material from the marked area.

c. Secure the wall box with 10-penny nails or #8 or

#10 screws, leaving the front edge ush with the surface.

d. Run all required cables (see steps 4, 5, and 6) and secure them with

cable clamps.

TIP: In order to t in the junction box, do not install a boot on TP

cables and RJ-45 connectors.

Step 2 — Disconnect Power

Disconnect all equipment power sources.

Step 3 — Connect Inputs to the Transmitter

z DVI or HDMI input connector — Connect a DVI or HDMI cable between this port and the output port of the digital video source.

z Local output (DTP DVI 230 D only) — If desired, connect a DVI monitor for local monitoring of the input digital image.

z DDC Route DIP switch (DTP DVI 230 D only) — If the local output is not used, set the

DDC Route DIP switch to remote. Ensure that you power the display before the video source.

z Audio input — Connect an unbalanced stereo audio source to this 3.5 mm mini stereo jack.

z RS-232/IR Pass-Through connector — Plug an RS-232 or modulated IR device into the RS-232/IR

Pass-Through port. Wire the cable as shown below.

Ground

Receive pin on connected unit

Transmit pin on connected uni

Connected RS-232

and IR Device Pins

Tx/Rx

Pins

Receive pin on connected unit

Transmit pin on connected uni

RxTx

RS-232 IR

RxTx

Signal Output

Cable

Clamp

Decora Faceplate

Extron

DTP DVI 230 D

Screws or

Nails

Wall opening is

ﬂush with edge of box.

Wall Stud

LOCAL OUT

Tx Rx G Tx Rx

RS-232

INPUTS

DVI-D

AUDIO

INPUTS

LOCAL OUT

DVI-D

AUDIO

Tx Rx G Tx Rx

RS-232

INPUTS

LOCAL OUT

DVI-D

AUDIO

REMOTE

DDC

ROUTE

LOCAL

Tx Rx G Tx Rx

RS-232 IR

1 2

INPUTS

AUDIO

Tx Rx G Tx Rx

RS-232 IR

OVER DTP

DTP DVI 230 D Tx DTP HDMI 230 D Tx

1 2

Résumé du contenu

Page 1 - Installation

DTP DVI 230 D and HDMI 230 D • Setup GuideThis setup guide provides instructions for an experienced installer to set up and operate the Extron DTP DVI

Page 2 - Operation

68-2367-50 Rev. A01 13Extron Headquarters+800.633.9876 Inside USA/Canada Only Extron USA - West Extron USA - East+1.714.491.1500 +1.919.850.1000+1.7

Commentaires sur ces manuels

Pas de commentaire

Extron-electronics DTP HDMI 230 D Setup Guide Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour la vidéo Extron-electronics DTP HDMI 230 D Setup Guide. Extron Electronics DTP HDMI 230 D Setup Guide User Manual [fr] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour la vidéo Extron-electronics DTP HDMI 230 D Setup Guide