Extron-electronics MPS 409 Setup Guide Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour la vidéo Extron-electronics MPS 409 Setup Guide. Extron Electronics MPS 409 Setup Guide User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 4
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
1
MPS 409 Setup Guide
Installation
Step 1 Disconnect Power
Remove power from the switcher and all other devices that will be connected.
1
MODE
2
SINGLE
1
SEPARATE
2
COMBINE DVI/HDMI
1
2
1
2
3
MUTE
MPS 409
DIGITAL MEDIA PRESENTATION SWITCHER
MUTE
VIDEO INPUTSHDMI INPUTS
MIC PROGRAM AUDIO
DVI INPUTSVGA/YUV INPUTS
CONFIG
EXEC
MODE
Step 2 Mount the Switcher
The MPS 409 is housed in a full rack width, 8.5 inch deep, 1U high metal enclosure. Select a
mounting location, then choose an appropriate mounting option and mount the switcher.
Step 3 Cable the Switcher
Make certain the MPS 409, all sources, and displays are powered off. Run all audio, video,
communication and power cables for operation.
a. Attach up to two VGA/YUV (
b
), two DVI (
l
), three HDMI (
f
), and two composite video (
h
)
input devices to the switcher.
b. Connect the VGA/YUV output (
c
), DVI output (
m
), HDMI output (
p
), and video (
r
) output
from the switcher to the appropriate display inputs.
c. For stereo input, connect up to nine audio sources to each of the unbalanced stereo audio
input groups; VGA/YUV (
d
), DVI (
n
), HDMI (
g
), and Video (
i
). See the 3.5 mm plug
connector diagram on the right for wiring.
50/60 Hz
100-240V 0.4A MAX
VIDEO
MPS 409
MIC/LINE
OFF MIC
OUTPUT
R
L
2
2
1
1
21
3
21
VGA/YUV HDMI
PROGRAM
AUDIO
OUT
L R
MIC/LINE
Tx Rx
RS-232
1 2
ON
LEVEL
+48V
ON LINE
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
DVI-D
21
21
2
1 3
1
2
R
L
R
L
l n o p q r sm
b c d f g h ie
This guide provides basic instructions for an experienced technician to install, set up, and
operate the Extron
®
Media Presentation Switcher, MPS 409. Where possible in the following
pages, line drawings are used to clarify steps discussed in the text. Installation and service
must be performed by authorized personnel only.
Unbalanced OutputBalanced Output
Tip
NO Ground Here
Sleeve(s)
Tip
NO Ground Here
L R
AUDIO
Tip
Ring
Sleeve(s)
Tip
Ring
L R
AUDIO
CAUTION
For unbalanced audio, connect the
sleeve(s) to the ground contact.
DO NOT connect the sleeve(s) to the
negative (-) contacts.
Tip (+)
Sleeve ( )
Sleeve ( )
Ring
(R+)
Tip (L+)
RCA Connector
3.5 mm Stereo Plug Connector
(unbalanced)
g. (Optional) If the switcher is connected to a computer or host
controller for remote control, connect the host RS-232 cable to the
3-pin captive screw connector on the rear of the switcher (see the
figure at right).
d. For unbalanced stereo output, connect an output device to each of the
output groups; VGA/YUV (
e
), DVI (
o
), HDMI (
q
), and Video (
s
).
See the 3.5 mm plug connector diagram on the right for wiring.
Ground ( _ )
Receive (Rx)
Transmit (Tx)
Bidirectional
RS-232
Device
Ground ( _ )
Receive (Rx)
Transmit (Tx)
RxTx
(5 mm)
MAX.
Do not tin
the wires!
Balanced Mic Input
Unbalanced Mic Input
(5 mm)
MAX.
Tip
Ring
Sleeve
Tip
Sleeve
50/60 Hz
100-240V 0.2A MAX
VIDEO
MPS 409
MIC/LINE
OFF MIC
OUTPUT
R
L
2
2
1
1
21
3
21
VGA/YUV HDMI
PROGRAM
AUDIO
OUT
L R
MIC/LINE
Tx Rx
RS-232
1 2
ON
LEVEL
+48V
ON LINE
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
DVI-D
21
21
2
1 3
1
2
R
L
R
L
e. Connect an audio amplifier to the Program Audio Output connectors.
See the connector diagram on the right for proper wiring.
f. (Optional) Connect a microphone to the rear Mic/Line connector
(see the figure at right). Refer to the microphone user guide for
proper wiring and phantom power requirements.
Set switch 2 of the DIP switch bank down (off) for a microphone. If
phantom power (+48V) is required, set switch 1 up (on).
Vue de la page 0
1 2 3 4

Résumé du contenu

Page 1 - Step 3 — Cable the Switcher

1MPS 409 Setup GuideInstallationStep 1 — Disconnect PowerRemove power from the switcher and all other devices that will be connected. 1MODE2SINGLE1S

Page 2 - Combined HDMI/DVI Mode

2MPS 409 Setup Guide (Continued)Single Switcher ModeSingle switcher mode emulates one switcher with 9 inputs (9x1). Only one input can be selected at

Page 3 - Setting the Microphone Level

3MPS 409 Setup Guide (Continued)In separate-combine mode, only one input selection is allowed from the HDMI/DVI groups along with a single input sel

Page 4 - X* * 2 # Thr X* ]

4MPS 409 Setup Guide (Continued)Extron USA - WestHeadquarters+800.633.9876Inside USA/Canada Only+1.714.491.1500+1.714.491.1517 FAXExtron USA - East+8

Commentaires sur ces manuels

Pas de commentaire