Extron-electronics SW RGBHV Series Setup Guide Manuel d'utilisateur télécharger pdf

This guide provides quick start instructions for an experienced installer

to set up and operate the SW RGBHV and SW RGBHV A

switchers.

Installation

Step 1 — Mounting

Turn off or disconnect all equipment power sources

and mount the switcher as required.

Step 2 — Inputs

• Connectupto2,4or6RGBHV,RGBS,

RGsB,orRsGsBsvideoorcomponent

video inputs to the Input connectors.

• Audio models —

Connectupto2,

4or6stereoormonoaudioinputs

to the 5-pin

captive screw

connectors.

Step 3 — Outputs

• ConnectanRGBHV,RGBS,RGsB,orRsGsBsvideoorcomponentvideodisplayor

other device to the Output connectors. Make connections as shown for step 3.

• Audio models —Connectabalancedorunbalancedstereoaudioormonoaudio

device to the 5-pin captive screw connector.

Connect the sleeves to ground (Gnd). Connecting the sleeve to a negative (-) terminal

will damage the audio output circuits.

Step 4 — Remote port

Connectahostdevice,suchasacomputerortouch

panelcontrolviaRS-232,OR connect a remote contact

closure device to the switcher

via the 9-pin D connector for

remote control of the switcher.

To command a switch under

contactclosurecontrol,

momentarilyshortaninput’s

pin on the remote connector to

ground(theswitchermustbein

normal [manual] mode).

For complete descriptions of remote control of the switcher using the applicable Simple

Instruction Set (SIS

™

) commands and/or the Universal Switcher Control Program, refer to

the full SWRGBHVSwitchersUser’sManual, available at www.extron.com.

Step 5 — Power

PlugastandardIECpowercordbetweentheswitcher’spowerconnectoranda100VACto

240VAC,50or60Hzpowersource.

Operation

Switch mode

SettherearpanelswitchtoAutoforautoswitchmode(theswitcherautomatically

switchestothehighest-numberedinputwithasyncsignalpresent)orNormalfor

manual switch mode. The front panel Auto Switch Active LED lights when the

switcher is in autoswitch mode.

Switch inputs in normal switch mode

Pressandreleasethedesiredinputbutton.

Adjust audio level (audio models)

You can set the input level of audio gain or attenuation via the front panel or the Remote port

tobecompatiblewithawiderangeoflinelevelsources.Individualinputaudiolevelscanbe

adjustedsothatthereisnonoticeablevolumedifferenceamongsources.Thisfunctionalso

eliminatestheneedforseparatepreampsorattenuators,whenusedwithprofessional(higher

line level) and consumer (lower line level) audio equipment.

Adjust the audio from the front panel as follows:

. Pressandreleasethedesiredinputbutton.

2. PressandholdtheAudioConf./SavebuttonuntiltheAudioConf./

SaveLEDbeginstoblink.Theapproximatelevelisindicatedbythe

inputLEDsandthepolaritybythe±dBLEDs.

The input LEDs display the approximate level of attenuation.

The +dB LED indicates the level is gain (positive).

The - dB LED indicates the level is attenuation (negative).

For details about reading the displayed value, refer to the

full SWRGBHVSwitchersUser’sManual, available at

www.extron.com.

3. Press and release the

and

buttonstoincreaseanddecreasetheaudiolevelby1dB

perpushofthebutton,orpressandholdthebuttonstoincreaseordecreasethelevel

by3dBpersecond.

4. PressandreleasetheAudioConf./Savebuttontoexit.TheAudio

Conf./SaveLEDgoesout.

Do not tin the wires!

Unbalanced Stereo Output Balanced Stereo Output

Ring

Sleeve(s)

Tip

Ring

Sleeve(s)

Tip

NO GROUND HERE.

L R

Unbalanced Stereo Input

Balanced Stereo Input

L R

Ring

Sleeve (s)

Tip

Sleeve

Tip

Sleeve

Tip

Ring

Do not tin the wires!

Setup Guide — SW RGBHV Series Switchers

Extron USA - West

Headquarters

+800.633.9876

Inside USA / Canada Only

+1.714.491.1500

+1.714.491.1517 FAX

Extron USA - East

+800.633.9876

Inside USA / Canada Only

+1.919.863.1794

+1.919.863.1797 FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+800.7339.8766

Inside Asia Only

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+400.883.1568

Inside China Only

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East

+971.4.2991800

+971.4.2991880 FAX

68-648-50

Rev. A

04 09

Setup Guide — SW RGBHV Series Switchers

CONF/SAVE

Press

and hold.

Conf/Save blinks.

Release the button.

-dB

+dB

Press Press

CONF/SAVE

Press

and release.

RGBHV

RGBS

RGsB,

RsGsBs,

Component

H/HV

Pin RS-232 Contact

closure

Function

1 — In#1 Input#1

2 TX

—

— Transmit data (-)

3 RX Receive data (+)

4 — In#2 Input#2

5 Gnd

RS-232 Protocol:

9600 Baud, 8, N, 1

Gnd Signal ground

6 — In#3

In#4

In #5

In#6

Input#3

Input#6

Input#4

Input #5

7 —

8 —

—

Female

AUTO

MANUAL

Press

and release.

Résumé du contenu

Page 1 - — Power

This guide provides quick start instructions for an experienced installer to set up and operate the SW RGBHV and SW RGBHV A switchers.InstallationStep

Commentaires sur ces manuels

Pas de commentaire

Extron-electronics SW RGBHV Series Setup Guide Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour la vidéo Extron-electronics SW RGBHV Series Setup Guide. Extron Electronics SW RGBHV Series Setup Guide User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour la vidéo Extron-electronics SW RGBHV Series Setup Guide