Extron-electronics Cable Cubby Lid and Trim Ring Replacement Kit (for Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Extron-electronics Cable Cubby Lid and Trim Ring Replacement Kit (for. Extron Electronics Cable Cubby Lid and Trim Ring Replacement Kit (for 300C, 300S, 600, 800) User Manual Manuel d'utilisatio

Lid and Trim Ring Replacement Kit for Cable Cubby models

300C, 300S, 600, and 800

Removing Old Trim Ring and Lid

1. Switch off all units, disconnect power and remove cables.

2. From under the table, loosen the wing nuts

and Phillips

head screws

3. Remove the table clamps from both sides of the cable

cubby. (Note the pegs

they sit on.)

4. Remove the cable cubby and set it upside-down on a thick

cloth to prevent damage to the table.

5. Remove the screws

connecting the old trim ring

(four screws for models 300C and 300S; six screws for

models 600 and 800.)

6. Unscrew the two retaining plates

capping the grooves

in which the pivot bar

is seated.

7. Remove the old lid

and pivot bar.

Table Clamps

Extron Electronics, USA

800.633.9876 714.491.1500

FAX 714.491.1517

Extron Electronics, Europe

+800.3987.6673 +31.33.453.4040

FAX +31.33.453.4050

Extron Electronics, Asia

+800.7339.8766 +65.6383.4400

FAX +65.6383.4664

Extron Electronics, Japan

+81.3.3511.7655

FAX +81.3.3511.7656

www.extron.com

68-1455-01

Rev A

09 07

Installing New Trim Ring and Lid

1. Unscrew the old lid from the pivot bar (four screws and

washers for all models).

2. Attach the old pivot bar to the new lid with the four

provided 4-40 3/8” L screws and washers.

Screws attaching the lid to the pivot bar come with washers

and are slightly longer than the screws for the trim ring,

which have no washers.

3. Slide the pivot bar

and lid

into the grooves of the

cubby hole

(located on the inside surface of the cubby

hole back supports) and reattach the two retaining plates.

4. Loosely attach the new trim ring to the cable cubby

with the provided 4-40 5/32” L screws.

5. Adjust the position of the ring so the lid opens and

closes freely. Then fully tighten the screws.

6. Replace the cable cubby.

7. Replace both table clamps on their original pegs.

8. Tighten the Phillips head screws and thumbscrews.

9. Adjust the hex nuts

in the cubby lid

, if necessary,

until the lid sits ﬂush with the trim ring.

10. Reconnect cables and power. Switch on units.

300C, 300S, 600, and 800 1

Résumé du contenu

Page 1 - 300C, 300S, 600, and 800

Lid and Trim Ring Replacement Kit for Cable Cubby models 300C, 300S, 600, and 800Removing Old Trim Ring and Lid1. Switch off all units, disconnect po

Commentaires sur ces manuels

Pas de commentaire

Extron-electronics Cable Cubby Lid and Trim Ring Replacement Kit (for Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Extron-electronics Cable Cubby Lid and Trim Ring Replacement Kit (for. Extron Electronics Cable Cubby Lid and Trim Ring Replacement Kit (for 300C, 300S, 600, 800) User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Extron-electronics Cable Cubby Lid and Trim Ring Replacement Kit (for