Extron electronics Cable Cubby 200, 300C, 300S, 600, 800 Manuel d'utilisateur télécharger pdf

Cable Cubby • Setup Guide

This guide provides instructions for an experienced installer to

install and connect the Extron Cable Cubby

300, 600, and 800.

The Cable Cubby units are furniture-mounted enclosures for cable access,

connections, and AC power. Cables that are not in use can be stored

out of the way while remaining connected to the presentation system.

Planning

Determine the best location for the enclosure. Before making any cuts:

c Ensure that the location where the Cable Cubby is to be installed is

convenient for as many users as possible.

c Ensure that the edge on which the lid opens is oriented correctly.

c Ensure that there is ample space under the table for cables.

c Ensure that the correct template or dimensions are used.

Decide on the method for cutting the hole in the table.

c Hand router and template

c CNC wood router

c Jigsaw and paper template

Before starting the installation, check with local and state regulations:

c Ensure that the planned installation complies with building and

electrical codes.

c Ensure that the planned installation complies with the Americans with Disabilities Act or other accessibility requirements.

Tools and Equipment Required for Installation

Safety Glasses

Phillips Screw Driver

Tape Measure

Vacuum Cleaner

1/4" Hex Nut Driver

Marking Pen

Square

Included Parts

Cable Cubby Enclosure (1)

300S 300C

800600

Zip Ties

Tweeker (1)

Screw Clamps (2)

AC Power Module

(quantity is optional,

depending on model)

#4−40 Screws & Nuts

Model

2 Pos

AAP Shelf Brackets

3 Pos

Grommet and

hole plug kit

CC 300 US/Int’l

CC 600 US/Int’l

CC 800 US/Int’l

0/2

0/0

2/0

4/2

0/2

4 Pos

0/0

4/2

L L-M

Pass through AAPs*

R-M R

1/1

2/3

0/0

2/2

3/3

1/0

2/1

3/2

2/1

*L = left, L-M = left-middle, R-M = right middle, R = right

Cable Cubby 600

1 2 3 4

Résumé du contenu

Page 1 - Cable Cubby • Setup Guide

Cable Cubby • Setup Guide1This guide provides instructions for an experienced installer to install and connect the Extron Cable Cubby® 300, 600, and 8

Page 2 - Preparing the Cable Cubby

2Preparing the TableWARNING: Wear safety glasses when cutting the hole in the table. Failure to comply may result in eye injury.ATTENTION:•The

Page 3 - Cable Cubby 800

3,5234Cable Cubby 300CSecure cables with zip tiesto holes on the bottomof Cable Cubby.Power CordConnect to AVdevice or system.Cable Cubby 800Mounting

Page 4 - Installation Checklist

68-1558-50 Rev B 05 124Installation ChecklistPlanning (page 1)  Choose a location. Consider the following:  Ensure that the edge on which the lid op

Plus de documents pour Mise en réseau Extron electronics Cable Cubby 200, 300C, 300S, 600, 800

Voir le document Extron electronics Cable Cubby 200, 300C, 300S, 600, 800 Manuel d'utilisateur

Extron electronics Cable Cubby 200, 300C, 300S, 600, 800 Manuel d'utilisateur (31 pages)

Extron electronics Cable Cubby 200, 300C, 300S, 600, 800 Manuel d'utilisateur (6 pages)

Commentaires sur ces manuels

Pas de commentaire

Extron electronics Cable Cubby 200, 300C, 300S, 600, 800 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Mise en réseau Extron electronics Cable Cubby 200, 300C, 300S, 600, 800. Cable Cubby 300/600/800 Setup Guide Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Mise en réseau Extron electronics Cable Cubby 200, 300C, 300S, 600, 800

Commentaires sur ces manuels

Produits connexes et manuels pour Mise en réseau Extron electronics Cable Cubby 200, 300C, 300S, 600, 800