Extron electronics MTP 1500RL 15HD A SEQ Manuel d'utilisateur télécharger pdf

MTP 1500RL 15HD A SEQ • Setup Guide

This guide provides basic instructions for an experienced installer to set up and operate the

Extron MTP 1500RL 15HD A SEQ twisted pair receiver.

For full details, see the MTP 1500RL 15HD A SEQ User Guide, available online at www.extron.com.

MTP 1500RL Series

POWER

12V

1.0A MAX

MTP 1500RL 15HD A SEQ

OUTPUT

MONO

AUDIO

RGB

PEAKING

LEVEL

DELAY

RED

GREEN

BLUE

SELECT

ADJUST

MIN/MAX

INPUT

BUFFERED OUTPUT

H +

V +

CSYNC

SOG

VIDEO

END

SPARE

MTP

Installation and Setup

Step 1 — Mounting

Turn off or disconnect all equipment power sources. Mount the MTP 1500RL 15HD A SEQ receiver as required.

Step 2 — Connect input

Connect the RJ-45 cable from an MTP transmitter to the Input port on the MTP 1500RL 15HD A SEQ receiver.

Terminate the cable as shown below right, using the same standard (A or B) at both ends.

Input

Source

MTP Tx

Device

Display

MTP RL Rx

Device

Input

Source

MTP Tx

Device

MTP 1500RL

15HD A Device

Display

1500 feet (457 m) maximum

Transmission distance with one device before the MTP 1500RL 15HD A SEQ

Transmission distance with more than one device before the MTP 1500RL 15HD A SEQ

VGA

cable

VGA

cable

MTP 1500RL

15HD A Device

1500 feet (457 m) maximum

VGA

cable

VGA

cable

NOTE: The transmitter and receiver are designed for and perform best with Extron Enhanced Skew-Free

™

AV cable

terminated in accordance with the TIA/EIA T568A standard. CAT 5 cables are acceptable but less preferable.

Using preterminated and tested cables is also recommended. Cables terminated on site should be tested before

use to ensure that they comply with Category 5 speciﬁcations.

Step 3 — Connect outputs

Attach the applicable output cables (video, audio, and buffered output).

a. High resolution video output — Connect a display device to the 15-pin HD connector (RGB).

b. Audio connector — Connect an audio device to the 5-pole captive screw connector for mono audio output

MONO AUDIO

Unbalanced Output

Balanced Output

Do not tin the wires!

Mono output 1-

Sleeve(s)

Mono output 1+

Mono output 2+

Mono output 2-

Sleeve(s)

Mono output 1

Mono output 2

NO GROUND.

CAUTION

For unbalanced audio, connect the sleeve(s) to the ground contact.

DO NOT connect the sleeve(s) to the negative (-) contacts.

c. Buffered output — Connect up to 5 daisy-chained MTP receivers to this RJ-45 connector.

CONTINUED ON SIDE 2

Pin T568A Wire

Color

T568B Wire

Color

1 White-green White-orange

2 Green Orange

3 White-orange White-green

4 Blue Blue

5 White-blue White-blue

6 Orange Green

7 White-brown White-brown

8 Brown Brown

RJ-45 Connector

12345678

Insert Twisted

Pair Wires

Pins:

1 2

Résumé du contenu

Page 1 - Installation and Setup

MTP 1500RL 15HD A SEQ • Setup GuideThis guide provides basic instructions for an experienced installer to set up and operate the Extron MTP 1500RL 15H

Page 2 - Step 7 — Skew compensation

MTP 1500RL 15HD A SEQ • Setup Guide (Continued)Extron Headquarters+800.633.9876 Inside USA/Canada Only Extron USA - West Extron USA - East+1.714.491.

Plus de documents pour Récepteur Extron electronics MTP 1500RL 15HD A SEQ

Voir le document Extron electronics MTP 1500RL 15HD A SEQ Manuel d'utilisateur

Extron electronics MTP 1500RL 15HD A SEQ Manuel d'utilisateur (4 pages)

Voir le document Extron electronics MTP 1500RL 15HD A SEQ Guide de l'utilisateur

Extron electronics MTP 1500RL 15HD A SEQ Guide de l'utilisateur (22 pages)

Commentaires sur ces manuels

Pas de commentaire

Extron electronics MTP 1500RL 15HD A SEQ Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Récepteur Extron electronics MTP 1500RL 15HD A SEQ. MTP 1500RL 15HD A SEQ Setup Guide Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Récepteur Extron electronics MTP 1500RL 15HD A SEQ

Commentaires sur ces manuels

Produits connexes et manuels pour Récepteur Extron electronics MTP 1500RL 15HD A SEQ