Extron electronics ECP 1000 Manuel d'utilisateur télécharger pdf (Page 8)

RCP 1000 • Operation

Operation, cont’d

Operation

3-2

Top Panel Controls

Figure 3-1 — RCP 1000 top panel

Picture control button — Allows you to toggle through the

center, size, filter, and contrast/brightness picture controls,

which are used to adjust the preview image. The program

image is not affected by these controls (unless the current

preview input is the same as the current program input).

Picture control LEDs — Indicate the active picture control.

Program input selection buttons — Allow the system operator

to view the image switch as it happens. The button for the

currently selected program input is lit.

Freeze — Locks the output display to the image that is currently

displayed on the program output.

When an image is frozen, a switch can still occur. When

the output is switched, the freeze command stays in effect.

To unfreeze the image, press the Freeze button.

If an image is frozen when a different input is selected or if

the unit loses power, the image unfreezes.

Black — Causes a black screen to be displayed. The black

screen can be switched by applying a cut or another effect.

A black input cannot be frozen.

RCP 1000

REMOTE CONTROL PANEL

PROGRAM

FREEZE BLACK 12345678

CUT TAKE

PPREVIEW

FREEZE BLACK 12345678

VERT HORZ

CONT BRIGHT

CENTER

SIZE

FILTER

COND/BRIGHT

TRANSITIONS

EFFECTS

COMMUNICATION

TAKE

FREEZE

BLACK

5 6

FREEZE

BLACK

CUT

1 2 3 4

1 – 8 — Selects the corresponding input to be displayed.

Normally, you will not use these buttons during a show. If

a program input selection button is pressed, the resulting

switch is not seamless.

Transition buttons — Control the type of switch that will occur

between program and preview outputs.

Cut button — Initiates an immediate seamless switch between

the program and preview images.

Take button — Initiates the switch selected by the effects

buttons.

Effects buttons — Control the effect, transition, and duration of

transition effects. The effects can have a transition time of

0.2 to 5 seconds.

SGS 408 Communication LEDs — Light to indicate that the

RCP 1000 is communicating with the SGS 408 unit. When the

RCP 1000 is transmitting data to the SGS 408, the Tx LED is lit.

When the RCP 1000 is receiving data from the SGS 408, the Rx

LED is lit.

Preview input selection buttons — Allow the system operator

to view the image before switching it to the program output.

The button for the currently selected preview input is lit.

Freeze — Locks the output display to the image that is currently

displayed on the preview output.

When an image is frozen, a switch can still occur. When

the output is switched, the freeze command stays in effect.

To unfreeze the image, press the Freeze button.

If an image is frozen when a different input is selected or if

the unit loses power, the image unfreezes.

Black — Causes a black screen to be displayed. The black

screen can be switched by applying a cut or another effect.

The black input cannot be frozen.

1 – 8 — Allow you to select the preview input device. The

button is lit while the input is active.

Adjustment knobs — Allow you to make adjustments to the

picture controls for the preview output. For example, if the

contrast/brightness picture control is active, turning the left

adjustment knob changes the contrast level, and turning the

right adjustment knob adjusts the brightness level.

3-3

im Vertrieb von

CAMBOARD Electronics

www.camboard.de

Tel. 07131 911201

Fax 07131 911203

[email protected]

1 2 3 4 5 6 7 8 9 10 11 12 13

Commentaires sur ces manuels

Pas de commentaire

Extron electronics ECP 1000 Manuel d'utilisateur Page 8

Commentaires sur ces manuels

Produits connexes et manuels pour Boîtiers de commutation en série Extron electronics ECP 1000