Extron-electronics HSA 822 User Guide Manuel d'utilisateur

Extron USA - WestHeadquarters+800.633.9876Inside USA and Canada Only+1.714.491.1500+1.714.491.1517 FAXExtron USA - East+800.633.9876Inside USA and Can

Cabling and Installing the AAPsNOTE: The online Connectivity Configurator, available at www.extron.com, offers guidance as to the fit of AAPs into th

Cabling the EnclosureBottom Panel Features33 54121Figure 8. HSA 822 Enclosure Underside Connectorsa RJ-45 connectors — See “Cabling the RJ-45 conne

Routing the AAP CablesThe AAP cables must have freedom of movement to permit opening and closing the surface mount enclosure. At the same time, they

Maintenance and ModificationsThis section describes modifying and maintaining the HSA 822 surface mount enclosures. Most of the maintenance procedur

Remove panel.Remove twoscrews ea. side.HSA 822COMPUTERINPUTSELECTAUDIOFigure 12. Removing the AAP Panel3. Disconnect any cables from the rear of th

Removing and Replacing the EnclosureThe procedures for replacing the gas lift and adjusting the levelling of the top surface require removing the HS

MountingSurfaceClamshellFull ThreadMounting BoltsAAP CablesFlat WasherPower CordRJ-45 ConnectorsCOMPUTERINPUTSELECTAUDIOHSA 822EnclosureRemove (16)s

4. Open and close the top panel as necessary to access the center lifting platform (see figure 17). Remove the four screws that secure the top panel

Adjusting the Top SurfaceThe top lifting panel of the HSA 822 can be adjusted to raise or lower its level flush with the flange. It can also be adjust

Adjusting the Top Surface LevelThe top lifting panel of the HSA 822 can be adjusted to ensure that the lifting panel is horizontal and not tipped.

Precautions This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with

ABCFigure 21. Clamshell DimensionsPart NumbersHSA 822 Part numberHSA 822 US Enclosure (black anodized) 60-570-01HSA 822 International Enclosure 60-6

If you choose not to use the metal routing template available from Extron, the cut-out template (see figure 23) will help you properly prepare the m

Package an HSA for shipment as follows:1. Contact the Extron S3 Sales and Technical Support Hotline to obtain a return kit. Extron will send the re

8. Insert the opposite end of the HSA 822 and the clamshell into the remaining foam shell (see figure 28). Firmly push the foam shells together as f

安全须知 • 中文这个符号提示用户该设备用户手册中有重要的操作和维护说明。这个符号警告用户该设备机壳内有暴露的危险电压，有触电危险。注意阅读说明书 • 用户使用该设备前必须阅读并理解所有安全和使用说明。保存说明书 • 用户应保存安全说明书以备将来使用。遵守警告 • 用户应遵守产品和用户指南上的所有安

ContentsIntroduction ...1About the HSA 822 Hideaway Enclosure ... 1Features ...

IntroductionThis section gives an overview of the Extron HSA 822 Hideaway Enclosure Series and describes its features. Topics that are covered inc

With an optional conversion kit, one or more of the RJ-45 (data) lines can be converted to an RJ-11 (telephone) line.The installed enclosure fits nea

InstallationThis section describes installation of the HSA 822, including connections and features. Topics that are covered include:• Installation

Preparing the Routing TemplateExtron offers a metal routing template for the HSA 822, part number 70-191-01. Extron recommends using this template a

Figure 4. Cutting the Opening with a RouterWARNING: Wear safety glasses when operating the router. Failure to comply can result in eye injury.4. U