Extron-electronics RGB 168xi VGA User Guide Manuel d'utilisateur Page 12

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 22
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 11
RGB 138
xixi
xixi
xi, RGB 168
xixi
xixi
xi Installation and Operation
RGB 138
xixi
xixi
xi, RGB 168
xixi
xixi
xi Installation and Operation
Installation and Operation, cont’d
2-13
HI
GH
VOL
TA
G
E
C
A
U
T
I
O
N
Adapter Plate
Tighten nuts
securely
RGB 138 xi
IN
P
U
T
S
A
U
D
IO
A
N
A
L
O
G
UNSWITCHED
600 WATTS MAX.
M
I
N
/
M
A
X
M
B
C
P
O
W
E
R
U
N
IV
E
R
S
A
L
IN
T
E
R
F
A
C
E W
/A
D
S
P
Cable Routing
Routing adapter output cables and
attaching adapter plates
6. Insert the adapter plate screws through the holes in the
interface front panel, as shown above. Attach the
adapter plates to the enclosure with the provided
captive washers and #4-40 nuts.
7. Gently pull excess cable(s) out the rear panel cable
clamp openings or, if a rear panel output adapter
plate is being used, connect the cable(s) to the plate
connector(s). Do not strain or damage the cable-
adapter connections.
8. Fasten the cables in place by tightening the screws on
the cable clamps provided on the rear panel openings.
100-240 50/60 Hz 0.5A
9. Replace the top cover on the interface, and fasten it with
the screws removed in step 2.
2-12
Adapter plates should be attached to the output cables and
interface before the interface is installed in a rack or in
furniture. The screws for installing the adapter plates are
built into the plates, so no additional screws will be needed.
Adapter plate installation must be performed
by authorized service personnel only.
Follow these steps to install adapter plates. The RGB 138xi
is shown for illustration, but the steps apply to both models.
1. Make sure that the power is removed from the interface
by disconnecting the AC power cord from the unit.
2. Open the cover of the interface (the top half of the
enclosure), as shown below. Remove the screws
from the enclosure, and lift the cover straight up.
Do not touch any switches or electronic
components inside the interface. Doing so
could damage the interface.
RGB 138
xi
R
G
B
1
3
8
x
i
IN
P
U
TS
A
U
D
IO
A
N
A
L
O
G
U
N
S
W
IT
C
H
E
D
6
0
0
W
A
TT
S
M
A
X
.
M
I
N
/
M
A
X
M
B
C
P
O
W
E
R
U
N
IV
E
R
SA
L
IN
T
E
R
FA
C
E
W
/A
D
S
P
Remove #8 Screws
(4 Places) Each Side
and Bracket, if Present
Remove (12)
Screws
Lift Cover
Straight Up
Opening the interface cover
3. Remove the blank plates from the interface by
unscrewing the nuts that fasten the plates to the
inside of the enclosure.
4. Route the adapter output cables through the rear panel
cable holes and clamps into the enclosure and out
the front panel plate openings, as shown on the
facing page.
5. Attach the output cables to the rear connectors of the
front panel adapter plates. Soldering will be
required for some connectors.
Vue de la page 11
1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 21 22

Commentaires sur ces manuels

Pas de commentaire