Extron-electronics DTP HDMI 230 Setup Guide Manuel d'utilisateur télécharger pdf

DTP HDMI 230 Tx Rear Panel

DTP HDMI 230 Rx Rear Panel

Front Panel

DTP HDMI 230 Rx

OVER DTP

RS-232

Tx Rx Tx RxG

POWER

12V

0.7A MAX

AUDIO

SIG LINK

DTP IN

OUTPUTS

AUDIO

INPUTS OVER DTP

RS-232

Tx Rx Tx RxG

POWER

12V

0.7A MAX

SIG LINK

DTP OUT

3 6

7 71 54 42

DTP HDMI 230 • Setup Guide

This guide provides quick start instructions for an experienced installer to set up and operate the

Extron DTP HDMI 230 digital video extender. The DTP HDMI 230 transmitter and receiver pair can

extend an HDCP-compliant HDMI signal up to 230 feet (70 m).

Installation

Step 1 — Mounting

Turn off or disconnect all equipment power sources and mount the Tx and Rx units as required.

Step 2 — Connections

HDMI Input connector (Tx) — Connect an HDMI

cable between this port and the HDMI output port of

the digital video source.

NOTE: See the “LockIt™ Lacing Brackets“on the back of this guide for to

securely fasten the input HDMI connector to the transmitter.

Audio input (Tx) — Connect an unbalanced stereo audio source to this 3.5 mm mini

stereo jack for an analog audio input.

RS-232 and IR connectors — To pass serial or infrared data or control signals, such as

serial control of a projector, connect the master device to the transmitter and the slave

device to the receiver via the RS-232 and IR captive screw connectors on both units.

DTP RJ-45 connectors — Connect transmitter DTP Out to receiver DTP In.

Extron recommends that you terminate both cable ends in accordance with the

following speciﬁcations, at a minimum:

z TIA/EIA T 568 B z CAT 6A, shielded

z 24 AWG, solid conductor

ATTENTION: Do not connect these devices to a computer data or telecommunications

network.

Signal LED — Lights when the unit is receiving a TMDS clock signal on the HDMI input (transmitter) or

any valid signal on the DTP In connector (receiver).

Link LED — Lights when a valid link is established between the units on the DTP cable.

HDMI Output connector (Rx) — Connect a display with an HDMI input for display of the

transmitted direct digital image.

NOTE: See the “LockIt™ Lacing Brackets“on the back of this guide for to

securely fasten the output HDMI connector to the receiver.

Audio Output connector (Rx) — Connect a balanced or unbalanced stereo or mono audio

device to the receiver via the Audio captive screw connector. See the drawing below.

Unbalanced Stereo Output Balanced Stereo Output

Do not tin the wires!

Tip

Ring

Tip

Ring

Sleeves

Tip

No Ground Here

Tip

Sleeves

ATTENTION: Connect the sleeves to the ground contact. DO NOT connect the sleeves to the negative (-) contacts.

Wire color

White-green

Green

White-orange

White-blue

Orange

White-brown

Brown

Blue

TIA/EIA T

568 B

TP Wires

12345678

Pins:

Ground

Receive pin on connected unit

ansmit pin on connected unit

Connected RS-232

and IR Device Pins

Tx/Rx

Pins

Receive pin on connected unit

ansmit pin on connected unit

RS-232

Tx Rx Tx RxG

AUDIO

OUTPUTS

AUDIO

INPUTS

1 2

Résumé du contenu

Page 1 - DTP HDMI 230 • Setup Guide

DTP HDMI 230 Tx Rear PanelDTP HDMI 230 Rx Rear PanelFront PanelDTP HDMI 230 RxOVER DTPRS-232IRTx Rx Tx RxGLRPOWER12V 0.7A MAXAUDIOSIG

Page 2 - LockIt™ Lacing Brackets

2g Power connector — Connect an IEC power cord between the included 12 VDC power supply and a 100-240 VAC, 50-60 Hz source. Connect the power supply

Commentaires sur ces manuels

Pas de commentaire

Extron-electronics DTP HDMI 230 Setup Guide Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour la vidéo Extron-electronics DTP HDMI 230 Setup Guide. Extron Electronics DTP HDMI 230 Setup Guide User Manual [fr] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour la vidéo Extron-electronics DTP HDMI 230 Setup Guide