Extron-electronics QGE 100 Setup Guide Manuel d'utilisateur télécharger pdf

Product Category

QGE 100 • Setup Guide

The QGE 100 Quantum Graphics Encoder encodes an RGB or DVI signal from a source computer or similar graphical device

and streams it to a Quantum

Elite Videowall Processor, computer, or other viewing device over an IP network. The viewing

device can then decode the image data and reproduce the original source image, displaying it at its original or scaled

resolution. The QGE is connected between a source computer and its monitor, keyboard, and mouse without affecting the

performance of the computer. From these connections it obtains data about changes in the display content, along with

keyboard and mouse actions.

NOTE: For full installation, conﬁguration, and operation details, see the QGE 100 User Guide at www.extron.com.

Rear Panel Features and Connections

COM 1

COM 2

DVI-I DVI-I

12V DC IN

REG

1.5A MAX

PERIPH PC

Refer all servicing to

qualiﬁed service personnel

1 2

Reserved for

Future Use

Installation Steps

1. Disconnect power from the QGE and power off all other equipment in the system.

2. Connect the QGE to the source computer:

NOTE: If you do not intend to use keyboard and mouse control of the source computer through the QGE 100, omit

the ﬁrst four bullets (connecting the QGE between the source computer and its keyboard and mouse).

z Connect the PS/2 mouse of the source computer to the QGE Periph mouse port (

in the diagram above).

z Connect the PS/2 keyboard of the source computer to the QGE Periph keyboard port (

z Connect the QGE mouse PC port (

) to the PS/2 mouse connector of the source computer.

z Connect the QGE keyboard PC port (

) to the PS/2 keyboard connector of the source computer.

z Connect the DVI-I In (

) monitor port of the QGE to the monitor port of the source computer.

z Connect the monitor of the source computer to the DVI-I Out loop-through connector (

) of the QGE.

3. Connect the QGE to the network. Connect the QGE Ethernet port to the network of your viewing device.

4. Connect power to the QGE 100 (see “Connecting Power to the QGE 100,” below).

NOTE: Always power up the QGE 100 before the source computer; otherwise, the QGE does not correctly detect

the mouse, keyboard, and monitor.

5. Power on the source computer.

CAUTION: Always power on the source computer and QGE 100 after making all connections between them.

Connecting Power to the QGE 100

1. Plug the mini DIN connector of the provided 12 VDC power supply into the rear panel connector labeled “12V DC.”

2. Connect the provided power cord between the IEC connector of the power supply and an AC outlet. (The QGE 100

power supply is double-insulated and does not require an earth to ground connection.)

Power connector

Ethernet port

Peripheral mouse connector

PC mouse connector

COM1 serial port

DVI-I In monitor port

DVI-I Out loop-through connector

PC keyboard connector

Peripheral keyboard connector

1 2 3 4

Résumé du contenu

Page 1 - QGE 100 • Setup Guide

Product Category1QGE 100 • Setup GuideThe QGE 100 Quantum Graphics Encoder encodes an RGB or DVI signal from a source computer or similar graphical de

Page 2 - Conﬁguring the QGE 100

QGE 100 • Setup Guide (Continued)2Front Panel FeaturesSTATUSLANQGE 100QUANTUM GRAPHICS ENCODER123a Power LED (green) — Lights when the unit has powe

Page 3 - Product Category

Product Category36. In the Network Settings section of the main window, enter the following multicast settings: z TTL (Time to Live): Enter the numb

Page 4 - www.extron.com

Commentaires sur ces manuels

Pas de commentaire

Extron-electronics QGE 100 Setup Guide Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour la vidéo Extron-electronics QGE 100 Setup Guide. Extron Electronics QGE 100 Setup Guide User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour la vidéo Extron-electronics QGE 100 Setup Guide