Extron-electronics CTL208CM Manuel d'utilisateur télécharger pdf (Page 8)

CTL208CM Control Panel Module • Installation

Installation, cont’d

Program the control panel module’s buttons as desired,

using either the Extron ICS100 control software or the

Extron serial character command set. See ICS100 Windows

Control Program and/or Serial Commands in chapter 4, Serial

Communications, for details.

If necessary, configure the control panel module’s serial

control protocol settings (baud rate, data bits, and stop

bits) to match those of the device to be controlled. See

ICS100 Windows Control Program and/or Serial Commands

in chapter 4, Serial Communications, for details.

If necessary, reconfigure the control panel module’s rear

panel DIP switch 1 to match the serial protocol (RS-232,

RS-422, RS-485) of the device to be controlled. See Rear

Panel Setup, in this chapter for details.

If the computer, control panel module, and the device to

be controlled are not part of an RS-485 serial port daisy

chain, disconnect the serial control cable from the

computer and install the serial control cable between the

control panel module and the device to be controlled.

If the rear of the control panel module will be inaccessible

when the installation is complete, the operation of the

module should be tested before the final mounting.

Apply or connect power to all devices in the system.

Test the system: Ensure that the controlled device

responds as desired to the control panel module buttons.

If necessary, correct the programming and/or the system

wiring. Ensure that you remove electrical power if you

need to change the system wiring. Test the system again.

Disconnect power from the control panel module and

other devices.

Mount the control panel module into any Extron four-

space mini-AAP connector panel.

If the rear of the control panel module will be inaccessible

when the installation is complete, all cables, including

the power connector on the CTL208, must be connected

before the permanent installation.

Mount the mini-AAP connector panel to the mini-AAP

mounting option as necessary. See Wall mounting in this

chapter for details about wall mounting the panel.

Restore power to all devices.

2-3

Installation Overview

CAUTION

Installation and service must be performed by

authorized personnel only. UL Listed electrical

boxes are recommended. See UL Requirements

for Wall Box Installation in this chapter.

If desired, order a custom engraved front panel. Contact

the Extron S

Sales & Technical Support Hotline to order

the panel.

Power off all devices and disconnect them from the

power source, if necessary.

Run a serial cable between the site where the CTL208CM

control panel module will be installed and the site of the

serial-controlled device.

For installation in a wall or furniture, prepare the site:

cut a hole in the surface, install the electrical box or

mounting bracket, and prepare the cables. See Wall

Mounting Site Preparation in this chapter. See appendix A,

Reference Information, for a partial list of devices that can

accept four space mini-AAPs.

For other installations, install a tabletop or in-table

connector bay, or other mini-AAP mounting option.

Refer to the manual for the device in which the control

panel module will be installed. See appendix A, Reference

Information, for a partial list of devices that can accept four

space mini-AAPs.

Connect a serial cable between the control panel module

and a computer. See Rear Panel Setup, in this chapter for

details.

Alternatively, you can connect the control panel module

to an RS-485 serial port daisy chain that includes the

programming computer and the device to be controlled.

In a daisy-chain configuration, you can make changes to

the control panel module’s button programming as

needed, without removing the panel from its installation.

If necessary, configure the control panel module’s rear

panel DIP switches to match the serial protocol (RS-232,

RS-422, RS-485) of the computer used to program the

control panel module. See Rear Panel Setup, in this chapter

for details.

Connect the power source to the control panel module.

See Rear Panel Setup, to wire the power connector.

Installation

2-2

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 24 25

Commentaires sur ces manuels

Pas de commentaire

Extron-electronics CTL208CM Manuel d'utilisateur Page 8

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Extron-electronics CTL208CM