Extron-electronics DVC 501 SD Setup Guide Manuel d'utilisateur télécharger pdf

Product Category

DVC 501 SD • Setup Guide

The Extron DVC 501 SD receives SD-SDI, HD-SDI, and 3G-SDI serial digital video signals and converts them to DVI-D and

analog RGB or component video. It is compliant with SMPTE 259M, 292M, 424M, and ITU digital video standards. The RGB

output can be set for RGBHV, RGBS, and RGsB. Bi-level or tri-level sync can be selected when the unit is set for component

video output. The DVC 501 SD features extraction of embedded AES3 audio, RS-232 and USB serial control, and a buffered

loop-through that delivers reshaped and restored multi-rate SDI signals.

NOTE: For full installation, conﬁguration, and operation details, see the DVC 501 SD User Guide, available at

www.extron.com.

Rear Panel Features and Connections

100-240V ~ 0.3A MAX

50/60 Hz

3G / HD / SD-SDI

BUFFERED

INPUT

LOOP-THROUGH

RGB/R-Y,Y,B-Y

OUTPUT

DVI-D

RS-232

N/A Tx

AUDIO

AC power connector

DVI-D output connector

Audio output connector

3G/HD/SD-SDI input connector

RGB/YUV output connector

RS-232 connector

Buffered Loop-through connector

Installation Steps

1. Disconnect power from all equipment.

2. (Optional) Mount the unit to a rack or furniture.

3. Connect the video input. Connect an SD-SDI, HD-SDI, or 3G-SDI source to the 3G/HD/SD-SDI port of the BNC input

connector (

in the rear panel illustration above).

4. (Optional) Connect a monitor or recording device. Attach a monitor or video recording device to the Buffered

Loop-through BNC connector (

5. Connect the video output. Connect a display or other output device to the DVD-D digital video connector (

) or to

the RGB/R-Y,Y,B-Y analog RGB (RGBHV, RGBS, and RGsB) or YUV component video connector (

6. Connect a control device. Connect a host device, such as a computer or touchpanel control system to one or both of

the following DVC ports to conﬁgure and control the DVC via Simple Instruction Set (SIS™) commands.

z RS-232 port (rear panel) — Connect a host device to the Tx, Rx, and

(ground) pins of this 5-pole captive screw

connector (

). The ﬁrst and second pins of this connector are not used. The default protocol for this port is

9600 baud, 1 stop bit, no parity, 8 data bits, and no ﬂow control.

z Cong port (front panel) — Connect a USB cable (USB A to USB mini B) between a USB port on your computer

and this port (

on the front panel illustration on the next page).

7. Connect the audio output. Connect an ampliﬁer or other audio output device to the 5-pole captive screw audio

connector (

on the rear panel illustration), as shown below.

Do not tin the wires!

Balanced Audio Output

Tip

Ring

Tip

Ring

Sleeves

Unbalanced Audio Output

Tip

Sleeves

CAUTION: For unbalanced audio, connect the sleeves to the ground contact. DO NOT connect them to negative (–)

contacts.

8. Connect power to the DVC 501 SD by plugging a standard IEC power cord (provided) from a 100 to 240 VAC, 50-60 Hz

power source into the power receptacle (

1 2

Résumé du contenu

Page 1 - DVC 501 SD • Setup Guide

Product Category1DVC 501 SD • Setup GuideThe Extron DVC 501 SD receives SD-SDI, HD-SDI, and 3G-SDI serial digital video signals and converts them to D

Page 2 - DVC 501 SD

Commentaires sur ces manuels

Pas de commentaire

Extron-electronics DVC 501 SD Setup Guide Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour la vidéo Extron-electronics DVC 501 SD Setup Guide. Extron Electronics DVC 501 SD Setup Guide User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour la vidéo Extron-electronics DVC 501 SD Setup Guide