Extron-electronics SME 100 User Guide Manuel d'utilisateur Page 33
- Page / 185
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
• Input #N (input video signal type) — This submenu is used to select a video signal
type for the currently selected input. N represents the selected input (1, 2, or 3).
To use this submenu:
• Rotate either Adjust knob to select a video signal type for the currently selected
input. See the "Available Input Video Signal Types" section on page 30 for
information on supported video signal types.
• Film Detect — This submenu is used to enable and disable 3:2 pulldown detection
for NTSC and 2:2 pulldown detection for PAL video sources. 3:2 pulldown and 2:2
pulldown (film mode) helps maximize image detail and sharpness for video sources that
originated from film.
When film detect is set to On, the SME100 recognizes signals that originated from
film and then applies video processing algorithms that optimize the conversion of video
that was made with the 3:2 or 2:2 pulldown process. This results in sharply detailed
images.
To use this submenu:
• Rotate either Adjust knob to turn film detect on or off. The default is Off.
• H Start (horizontal start) and V Start (vertical start) — This submenu is used to set
the horizontal and vertical start positions of the active video for the selected input.
To use this submenu:
• Rotate the horizontal ([) Adjust knob to change the horizontal start pixel position
(left edge) of the active video for the selected input. The default is 128.
• Rotate the vertical ({) Adjust knob to change the vertical start line position
(top edge) of the active video for the selected input. The default is 128.
• TTLPIX (total pixels) and Phase (pixel phase) — This submenu is used to set the
total pixels and pixel phase of the active video for the selected input.
To use this submenu:
• Rotate the horizontal ([) Adjust knob to change the width (in pixels) of the total
display area to be sampled for the selected input.
• Rotate the vertical ({) Adjust knob to move the pixel sampling point for the selected
input. The range of settings is 0 to 31. The default is 16.
• H Active (horizontal active pixels) and V Active (vertical active lines) — This
submenu is used to set the horizontal active pixels and vertical active lines of the active
video for the selected input.
To use this submenu:
• Rotate the horizontal ([) Adjust knob to change the width (in pixels) of the active
video for the selected input.
• Rotate the vertical ({) Adjust knob to change the height (in lines) of the active video
for the selected input.
• EDID Input N — This submenu is used to select an EDID to apply to the selected
input. N represents the selected input (2 or 3). This menu is used with the 15-pin HD
and DVI inputs only (inputs 2 and 3).
To use this submenu:
• Rotate the horizontal ([) Adjust knob to change the resolution of the selected
input. The default input resolution is 1024x768.
• Rotate the vertical ({) Adjust knob to change the refresh rate of the selected input.
The default input refresh rate is 60 Hz.
SME100 • Front Panel Operation 27
- User Guide 1
- Safety Instructions 2
- FCC Class A Notice 3
- Specifications Availability 4
- Contents 5
- SME 100 • Contents vi 6
- Introduction 7
- SME100 • Introduction 2 8
- Suggested PC Requirements 9
- Features 10
- SME100 • Introduction 5 11
- SME100 • Introduction 6 12
- Definitions 13
- SME100 • Introduction 8 14
- SME100 • Introduction 9 15
- SME100 • Introduction 10 16
- STREAMING MEDIA ENCODER 17
- S-video (YC) 18
- Balanced Audio Output 19
- Unbalanced Audio Output 19
- Connected RS-232 20
- Device Pins 20
- Modes 4 and 5 21
- Hardware Setup Overview 23
- SME100 Power Up Procedure 24
- SME100 Network 25
- Configuration 25
- Protocols Used for Streaming 26
- SME 100 sends data to 27
- Front Panel 28
- Operation 28
- select a submenu option 29
- User Presets 30
- Encode Presets 31
- Streaming Presets 32
- 00000 00000 37
- 0640 0480 37
- 064 064 37
- • Video / Audio 39
- • Video only 39
- 1 to 30. The default is 30 40
- Stream Config Menu 41
- Advanced Config Menu 42
- About the Auto Memory Submenu 44
- About the Auto Image Submenu 46
- Comm Settings Menu 49
- IP), subnet mask (SM), and 50
- GM) submenus (see figure 25) 50
- Settings menu 50
- Default Display Cycle 51
- Web-based User 52
- Interface Operation 52
- SME100 Media Players 53
- Live View Page 54
- Stop button 55
- Live View Page Notifications 56
- Installing Media Players 57
- Windows (see figure 32) 58
- Run to begin the download 59
- Next to 60
- OK (see figure 44) 64
- Next (see figure 45) 65
- Next (see figure 46) 65
- Install 66
- Using VLC 70
- Tools menu, select 71
- Video Effects tab and under 71
- Using QuickTime Media Player 72
- Status Page 73
- Configuration Page 75
- File Management Page 75
- Adding Directories 77
- Uploading Files 78
- Saving Files 78
- Managing Files Using FTP 79
- Backup / Restore Page 80
- Control Page 83
- 2a 2b 2c 2d 2e 2f 2g 2h 2i 84
- User and Input Presets 88
- Saving or recalling presets 89
- Renaming presets 89
- Web-based 90
- System Settings Page 91
- II) [RFC 1213] 93
- Encoder Settings Page 94
- Using Encoding Presets 102
- Using Streaming Presets 103
- Live View Settings Page 104
- Embedding the SME100 Stream 107
- Port Settings Page 109
- Advanced Settings Page 111
- Creating a Custom EDID 113
- Matrix Switcher Syncing 115
- Advanced Settings 117
- Disabling Sync to Matrix 118
- Security Page 119
- Firmware Upgrade Page 121
- Reset Page 122
- Communication and 123
- Software Overview 124
- Installing the software 125
- Running DataViewer 125
- Enter SIS 126
- Commands 126
- Responses 126
- USB tab 128
- Using Telnet 129
- SME100-initiated Messages 130
- Error Responses 131
- 06 / 14 / 11 – 13 : 40 : 03 136
- 137
- SME-100-HD/SD-00-02-3D 138
- E13 error 138
- View GMT offset 153
- Set daylight savings 153
- 192.168.254.254, and the 159
- 255.255.0.0 159
- Power Save Mode 161
- Reference 162
- Information 162
- Streaming Playback Methods 163
- 192.168.254.254 164
- Please enter a network URL 165
- (SAP) (see figure 108) 167
- Available Unicast Streams 170
- Available Multicast Streams 171
- IP Addressing 172
- Subnet Mask 173
- Port Number 173
- Choosing IP Addresses 173
- Response Messages 174
- Pull streaming (RTSP) 175
- SME100 Firmware Updates 176
- Browser Configuration 178
- Sites button and allow the 179
- Plugin Compatibility 182
- Player Compatibility 183
- Media Server Compatibility 183
- Mounting the SME100 184
- Contact Information 185
- Extron Warranty 185
Produits connexes et manuels pour Matériel Extron-electronics SME 100 User Guide
(2 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.100 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels